4.3 The socket fusion, butt fusion, and saddle fusion procedures in this practice are suitable for joining PE gas pipe and fittings, PE water pipe and fittings, and PE general purpose pipes and fittings made to PE product specifiions from organizations such as ASTM, AWWA, API, and ISO that are used in pressure, low pressure and non-pressure appliions.
The pipe ends are then faced (machined) to mechanical stops to ensure clean, parallel pipe ends for the heating process. The pipe ends are then aligned using the clamps on the fusion machine. A temperature controlled heater is installed in the machine and the pipe ends are heated according to the butt fusion standard ASTM International F2620.
ASTM D 3035-03a, Standard Specifiion for PE Plastic Pipe Based on Controlled Outside Diameter; ASTM D 2657-03, Standard Practice for Heat Joining Polyolefin Pipe and Fittings; ASTM D2683-98, Standard Specifiion for Socket-Type Polyethylene
Chapter 9 PE Pipe Joining Procedures 328 The principle of heat fusion is to heat two surfaces to a designated temperature, then fuse them together by appliion of a sufficient force. This force causes the melted materials to flow and mix, thereby resulting in fusion.
ASTM F1056 - Standard Specifiion for Socket Fusion Tools for Use in Socket Fusion Joining Polyethylene Pipe or Tubing and Fittings Published by ASTM on February 1, This specifiion covers socket fusion tools for use in making socket fusion joints between polyethylene pipe or tubing and fittings as specified by Specifiions D3035, D2513, and D2683.
ASTM D3035: Standard Specifiion for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter. ASTM F2620-06: Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings ASTM D2683: Standard Specifiion for
The standard length of HDPE pipe is 50 feet, in sizes above 2” in diameter with longer lengths available on request. ... • Pipe dimensions are in accordance with ASTM F714 and AWWA C906. • Pressure ratings are for water at 73.4 deg F. • Some of the pipe ...
All threaded connections shall have pipe threads designed in accordance with the requirements of ASTM D2464, which references ANSI B1.20.1 (formerly B2.1) for tapered pipe threads (NPT). Pipe, valves, fittings and joining equipment shall be supplied by a single source provider to insure compatibility of system components and to assure proper joint integrity.
Heat Fusion Joining of Polyethylene Pipe and Fittings1 This standard is issued under the ﬁxed designation F2620; the nuer immediately following the designation indies the year of original adoption or, in the case of revision, the year of last revision.
HDPE Pipe Specifiions Pacific Corrugated Pipe HDPE pipe for sale Phone: (949) 650-4555 Toll Free: (877) 874-7443 Fax: (949) 650-0781 ... (Gaskets) for Joining Plastic Pipe ASTM D 3212 - Standard Specifiion for Joints for Drain and Sewer Plastic Pipes Using ...
F3190-16 Standard Practice for Heat Fusion Equipment (HFE) Operator Qualifiion on Polyethylene (PE) and Polyamide (PA) Pipe and Fittings pipe fittings~ personnel qualifiion~ polyethylene pipes~ training~ 1.3 The HFE operator training and qualifiion shall be for butt fusion for either PE or PA piping products, using the specific brand and size range of fusion …
HDPE Potable Water Industry Standards: AWWA, ASTM, CSA, NSF ASTM D2239 Standard Specifiion for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter ASTM D2321 Standard Practice for Underground Installation of
b. Mechanical couplings designed for joining HDPE pipe or for joining HDPE pipe to another material. 188.8.131.52 Mechanical couplings shall be fully pressure-rated and fully thrust-restrained such that if installed in accordance with manufacturer’s
Yes. In Deceer 2006, ASTM published a new standard for fusion joining PE pipe and fittings, ASTM F2620. In May, 2007, ASTM D2657 was republished with a revision that removed PE pipe and fittings joining. Specifiions that reference ASTM D2657 for
specifiions aPPlicable StandaRdS aStm f2306, Standard Specifiion for 12” to 60” (300 to 1500 mm) Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Gravity-Flow Storm Sewer and Subsurface Drainage Appliions aStm d2321, Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity
1.3 The electrofusion joining technique described can produce sound joints between polyolefin pipe and fittings, provided that all products involved (that is, pipe and fittings) meet the appropriate ASTM specifiions. 1.4 This practice is not limited by pipe or fitting size, however additional steps or procedures may be necessary when electrofusion joining to pipe of larger …
HDPE pipe and fittings manufacturers have approved PPI’s Generic Joining Procedures in an attempt to standardize the joining procedures of HDPE. For socket fusion, ASTM standard F1056 is referenced. DO NOT join Driscopipe 7000 or 8000 series products
Pipe sizes 3” and large shall have a manufacturing standard of ASTM F 714, while pipe smaller than 3” shall be manufactured to the dimensional requirements listed in ASTM D 3035. Dimension Ratio (DR) and Outside Diameter (IPS/DIPS) shall be as specified on plans.
Piping Systems which includes, pipe, fittings, joining equipment, and installation training. GF HDPE (High Density Polyethylene) ... Standard Ratings • ASTM D638 • ASTM D2837 • ASTM D3035 • FDA CFR 21 177.160 • FDA CFR 21 178.3297 • NSF 61 ...